Posts mit dem Label DDWRT werden angezeigt. Alle Posts anzeigen
Posts mit dem Label DDWRT werden angezeigt. Alle Posts anzeigen

Mittwoch, 8. August 2012

Your home lab costs too much electricity?


ust found out my electricity bill is going up by 19% and its already stupidly high as it is. So I decided to save my own pocket to go green in what way I can. So #1 of course I’ve got my home vSphere cluster properly configured to keep off one of my servers switched off most of the time using DPM. However I want to save more energy so I had an idea about my desktop PC. Like most IT geeks I leave my home desktop PC switched on 24/7  for convenience, to have access whatever the reason I like to have it on.  I started to  think is there a way I can control my desktop PC like DPM and came up with this idea: I would schedule a task to place my PC into sleep mode at 2am and then schedule a Wake Up Lan task to power it on in its previous state at 7am thus saving me 5 hours of electricity. So this is how I did it:
Step1 I used the windows scheduler to schedule this command at 2am:
Click to make larger
This places my PC in a sleep state.
 Step 2. I run the DD-WRT firmware on my home router (DD-WRT is configurable on tons of routers) and one of the things it can do is schedule through a cron job a wake up lan call (WOL) . Below is the command I used to wake up using my PC from its MAC address at 7:03am:
Click to make larger
Job done..
Popularity: 4% [?]

Samstag, 9. Juni 2012

Building a DD-WRT Image In vSphere 5.0


Introduction

I have a need to put a router between my test ESXi 5.0 server and my network. At home, I use a Linksys E3000 (both 2.4Ghz & 5Ghz Wireless-N, gigabit) router, with OpenSource DD-WRT custom firmware. There is a x86 variant that can be downloaded, people mention in the forums about using it on old PCs, I thought I would give making a VM a go.

Pre-Requisites

    1. An installed copy of ESXi 5.0 (this is almost certain to work on 4.0, but not 3.5)
    2. The DD-WRT x86 Image. I chose the VGA public image. This is a free version, limited to 4096 connections (fine for my purposes) and without Wi-Fi support. The image that is used is here.
    3. physdiskwrite – A Windows tool for writing raw images to a hard disk.
    4. An existing Windows image.
      Installation

      Creating the Virtual Machine

  1. Create a virtual Machine. Select a configuration type of Custom.
    New_VM_-_Custom
  2. Name the VM something appropriate.
  3. Select a datastore for the Virtual Machine.
  4. Select ‘Virtual Machine Version: 8’ (if using ESXi 4.0, using version 7)
    New_VM_-_Virtual_Machine_Version
  5. For Guest Operating System type, choose ‘Linux’ and select ‘Other 2.6.x Linux (32-bit) from the drop down.
    New_VM_-_Guest_Operating_System
  6. Choose 1 virtual sockets, with one core per virtual socket.
    New_VM_-_CPUs
  7. Choose 512MB RAM.
    New_VM_-_RAM
  8. Select the appropriate number of NICs (nearly always 2), E1000, and choose the port groups. (I have found that the first NIC is assigned to the WAN)
    New_VM_-_NICs
  9. SCSI Controller, choose any. This will be replaced.
  10. Choose not to create a disk.
    New_VM_-_No_Disk
  11. Tick Edit the virtual machine settings before.
  12. In the Virtual Machine Properties, click Add. Select Hard Disk.
    New_VM_-_Add_Hard_Disk
  13. Select ‘Create a new virtual disk’
    New_VM_-_Create_New_Virtual_Disk
  14. Make the capacity of the disk 1GB. I chose to make it Thin Provisioned.
    New_VM_-_1GB_Cpacity
  15. Set the Virtual Device Node to IDE (0:0)
    New_VM_-_IDE
  16. Press OK, then Finish. Wait for the VM to be created.

Install the image to the Disk

  1. Choose your Windows VM. Power it off if necessary.
  2. Edit the Windows VM’s properties. Press Add.
  3. Select a Hard Disk.
  4. Choose ‘Use Existing Virtual Disk’
    Edit_VM_-_Add_Exiting_Virtual_Disk
  5. In Advanced Options, ensure that the Virtual Device Node is ‘IDE (0:0)’
  6. Click OK, then Finish. Power on the Windows VM.
  7. Load PhysGUI (make sure you elevate it)
  8. Ensure that you select the ‘VMware Virtual IDE Hard Drive ATA Device’, right click select ‘Image laden’ –> ‘Öffinen’. Select the downloaded DD-WRT image.
    PhysGUI_-_Select_Image
  9. Click OK through the prompts.
    PhysGUI_-_Remove_2GB
  10. Wait until the disk completes writing. Shut down the VM.
    PhysGUI_-_Write_to_Disk
  11. Edit the Windows VM’s properties. Select the DD-WRT virtual disk and press remove. Ensure ‘Remove from virtual machine’ is selected. Click OK.
  12. Start up the DD-WRT VM.

Connecting to the Router

    1. Load another VM on the same LAN as the router. Ensure that it is configured to automatically obtain an IP address.
    2. It should be assigned an IP by the DD-WRT router’s DHCP server service. You can see this by performing an ipconfig (if using a Windows client)
    3. Presuming that you have an IP address, use the web browse to connect to 192.168.1.1
      DD-WRT_System_Information
    4. It will ask to set the username and password. Note that if you SSH into the router at a later point, it will use the username ‘root’ with the password set here.
      DD-WRT_-_Set_Creds
    5. You are presented with the DD-WRT System Information page. This will show the current hardware, configuration, DHCP client list, etc.
Wenn euch das zu viel arbeit ist könnt ihr auch hier die fertige VM herunterladen



Rename Onedrive Business root folder

Rename Onedrive Business root folder Here is what I remember: In the Office 365 web admin pages, change the organization name to a shorte...